Looking across a longrun roof from the scaffold, hills behind Roof Calc Pro

Roof Calc Pro

Start your 7-day free trial Sign in

Rake

Every sheet up the rake, worked out before you cut

Put in the cover and the pitch. You get the rake on one sheet, then the whole run off it, sheet by sheet, up to the longest sheet you can get.

The last one is usually a part cut. It tells you where to mark it and how far across to run the diagonal.

At 760 cover and 25 degrees that’s 838.57 a sheet and eight sheets to six metres. The eighth is marked at 5869.99 up the edge, with the diagonal 117.83 across.

The Rake tab: 760 cover at 25 degrees gives a rake length of 838.57 mm and a cut angle of 47.81 degrees
760 cover, 25 degrees.
The cut list: sheets 1 to 7 from 838.57 to 5869.99 mm, then sheet 8 as a part cut marked at 5869.99 with the diagonal 117.83 mm across
The cut list, with the part cut on sheet 8.
Width

Sheets across a face, and the triangle base

Sheets across: put in the face width, the cover and the sheet length. It counts the full sheets, gives you the slither to rip, and the lineal metres. A six metre face in 762 cover is seven full sheets and a 666.00 slither, 48 lineal metres. One switch drops the slither if you’re not running it.

Triangle base: put in a sheet length and the pitch, and it draws the triangle on the roof face to scale. A 6000 sheet at 25 degrees has a base of 5437.85 and a raking edge of 8097.54.

Sheets across a 6000 mm face at 762 cover: 8 sheets, 7 full, a 666.00 mm slither rip, 48.0 lineal metres, with the face drawn as numbered strips
Six metre face, 762 cover, six metre sheets.
Triangle base for a 6000 mm sheet at 25 degrees: base 5437.85 mm, raking edge 8097.54 mm, drawn to scale
A 6000 sheet at 25 degrees, drawn to scale.
Nelson and Tasman Bay from the hills, one of Tiaki's own photos

Nelson from the hills. Most of the roofs this gets used on are down there.

Wall

Gable ends and walls, every sheet listed

Put in the cover and the pitch and you get the rise per sheet. Then say where the first sheet starts and how many sheets, and it lists every length.

760 cover at 5 degrees rises 66.49 a sheet. Start at 300 and the twelfth sheet is 1097.88. Anything over your longest sheet gets flagged.

The Wall tab: 760 cover at 5 degrees gives a height of 66.49 mm per sheet
760 cover, 5 degrees.
The Wall cut list: rise per sheet at 760 cover 66.49 mm, twelve sheets from 366.49 to 1097.88 mm
Twelve sheets from a 300 start.

838.57, not 839.

Some cuts can’t be rounded. Every length, slither and mark has its exact figure to two decimal places, and the cut list you copy or share carries the same figures as the screen.

Every run also says what it steps by and the cover it came from, in plain words: “Rake per sheet at 760 cover: 838.57 mm.” So you can check it before you cut.

Valley

Valley cuts, both sides

Where a flatter roof runs into a steeper one, it works out the cut on each side of the valley, with the steps to mark and cut it.

1015 sheets at 37.5 and 8 degrees: 234.33 on the steep side, 5596.17 on the flat side. That steep-side figure was checked on a real valley, where it measured about 230.

It assumes the two roofs meet square, and the screen says so.

The Valley tab: 1015 sheets at 37.5 and 8 degrees, steep-side cut 234.33 mm exact, flat-side cut 5596.17 mm exact
1015 sheets, 37.5 into 8 degrees.
Pitch meter

Read the pitch off the sheet

Stand the phone on its long edge on the sheet, like a level, or lay it flat. It works out which way it’s sitting and reads the pitch.

Tap Rake, Wall or Width and the pitch goes straight in.

The Pitch Meter screen with the roof pitch dial and buttons to use the pitch in Rake, Wall or Width
Taken on a computer, so it reads 0.0. On a phone it reads the roof.
On the scaffold of a new build above Tasman Bay, one of Tiaki's own site photos

On the scaffold above the bay. This is where the numbers get used, between the framing and the first sheet.

What it costs

Seven days free, then $9 a month incl. GST. Card to start, cancel any time.

It runs in the browser on your phone or computer. Add it to your phone’s home screen and it opens like an app.

Start your 7-day free trial Sign in